*these two values are inter-dependent. recommended operating conditions min max unit v cc dc supply voltage 4.5 5.5 volt v i dc input voltage range 0 v cc volt v o dc output voltage range 0 v cc volt p w* pulse width % of total delay 40 % d * duty cycle 40 % t a operating free air temperature 0 70 c i o dc output source/sink current 25 ma schematic input pulse test conditions @ 25c unit e in pulse input voltage 3.2 volts p w pulse width % of total delay 150 % t ri input rise time (0.75 - 2.4 volts) 2.0 ns p rr pulse repetition rate @ pw 500ns 1.0 mhz pulse repetition rate @ pw > 500ns 100 khz v cc supply voltage 5.0 volts dc electrical characteristics test conditions min max unit v ih high level input voltage v cc = 4.5 to 5.5 2.0 volt v il low level input voltage v cc = 4.5 to 5.5 0.8 volt v oh high level output voltage v cc = 4.5v,i o =-4.0ma 4.0 volt @v ih or v il v ol low level output voltage v cc = 4.5v,i o = 4.0ma 0.3 volt @v ih or v il i l input leakage current v cc = 5.5v @v ih or v il 1.0 ua i cc supply current v cc = 5.5v, v in =0 15 ma t ro output rise time (.75 - 2.4 volts) 4 ns parameter n h high fanout lsttl load v cc = 5.5v, v oh = 4.0v 10 8 pin 5 tap high speed cmos (hct) compatible active delay lines 12* 17 22 27 32 epa1130-32 epa1130g-32 12* 18 24 30 36 epa1130-36 epa1130g-36 12* 19 26 33 40 epa1130-40 epa1130g-40 12* 20 28 36 44 epa1130-44 epa1130g-44 12* 21 30 39 48 epa1130-48 epa1130g-48 12* 22 32 42 52 epa1130-52 epa1130g-52 12* 24 36 48 60 epa1130-60 epa1130g-60 15 30 45 60 75 epa1130-75 epa1130g-75 delays are 5% or 2 ns? dip part smd part tap total number number delays are 5% or 2 ns? dip part smd part tap total number number 20 40 60 80 100 epa1130-100 epa1130g-100 25 50 75 100 125 epa1130-125 epa1130g-125 30 60 90 120 150 epa1130-150 epa1130g-150 35 70 105 140 175 epa1130-175 epa1130g-175 40 80 120 160 200 epa1130-200 epa1130g-200 50 100 150 200 250 epa1130-250 epa1130g-250 60 120 180 240 300 epa1130-300 epa1130g-300 70 140 210 280 350 epa1130-350 EPA1130G-350 ? whichever is greater. delay times referenced from input to leading edges at 25c, 5.0v. * inherent delay dsa1130/g rev. b 3/27/01 qaf-cso1a rev. b 8/25/94 unless otherwise noted dimensions in inches tolerances: fractional = 1/32 .xx = .030 .xxx = .010 16799 schoenborn st. north hills, ca 91343 tel: (818) 892-0761 fax: (818) 894-5791 e l e c t r o n i c s i n c . 29 epa1130-500 epa1130-500 500 400 300 200 100 72635 1 4 output ground input 8 vcc smd package dip package .365 max. .500 max. .280 max. pca epa1130-32 d.c. .010 typ. .120 min, .020 typ. .250 max. .020 typ. white dot pin#1 .100 .100 pca epa1130g-32 d.c. .280 max. .500 max. .250 max. .01 typ. .400 max. .02 .050 .300 .100 .055 .410 .03 pad layout
|
